Focal 8 Speaker Plug & Play Bundle Installation Guide | 2010-2024 4Runner

Focal 8 Speaker Plug & Play Bundle Installation Guide | 2010-2024 4Runner

Install Your Focal 8 Speaker Plug & Play Bundle!

Here is a simple and easy breakdown of how to install you new
Focal 8 Speaker bundle for your 2010-2024 Toyota 4Runner.

Tools needed:
  • Ratchet wrench
  • 10mm socket
  • T20 torx bit
  • Panel removal tool
  • Phillips head screw driver
Step 1

Remove the dash tweeters:
  • Using a panel removal tool pry up on the speaker grille on the dash.
  • Using a 10mm socket or wrench remove the two bolts that secure the factory tweeter.
  • Depress the tab and remove the speaker connector.
  • Remove the factory tweeter bracket from the speaker by removing the two T20 torx screws or 10mm bolts.
  • Use a small flat head screw driver to release the connector from the bracket.
Repeat the process for the other tweeter.

Step 2

Installing the Focal dash tweeters:
  • In the box you will find the provided Focal tweeter assembly.
  • Connect the connector to the factory wiring from your dash.
  • Line up the two factory mounting hole and use the factory 10mm bolts to secure the tweeter assembly.
  • Remove the protective plastic and tape.
  • Replace the tweeter grille and the A-pillar trim.
  • Secure the A-pillar trim with the two factory 10mm bolts and close the covers.
Step 3

Removing the front door panel:
  • Remove the plastic trim panel from near the mirror by pulling out with your fingers.
  • Remove the cover panel behind the door handle by prying out the cover with a panel tool.
  • Open the cover near the top of the grab handle to reveal a phillips head bolt.
  • Open the cover at the bottom of the grab handle to reveal a phillips head bolt.
  • Remove the three phillips head bolts using a screwdriver.
  • Remove the door panel by grabbing the bottom of the panel and pull back with your fingers.
  • Lift the door panel up and off the window ledge.
  • Disconnect the door latch and locking wire by removing the connector from the hold, swivel the ball up and out of the mechanism.
  • Depress and remove the connections for the window switch and courtesy light.
  • If any of the retaining clips for the door panel stayed in the door, now is the time to remove them using a panel removal tool and insert them back into the door panel.
Step 4

Removal and replacement of the 6x9 door speaker:
  • Disconnect the factory speaker wire from the top of the speaker by depressing the tab.
  • Using a 10mm socket, remove the four screws that secure the factory speaker.
  • Place the Focal speaker into the opening, making sure to line up all four holes to the factory mounting location.
  • Secure the speaker to the door using the factory screws.
  • Connect the door speaker harness into the speaker housing.
Repeat the process for the other front door speaker.

Step 5

Replace the front door panel:
  • Connect the window switch panel, courtesy light, door lock wire and door handle wire.
  • Hang the door on the window ledge and push down into place.
  • Once the door panel is lines up, push in to secure the retaining clips.
  • Secure the three phillips head screws: Located behind the door handle, at the top of the grab handle and at the bottom of the grab handle.
  • Replace the cover plate behind the door handle.
  • Replace the trim piece near the mirror.
Step 6

Removing the rear door panel:
  • Remove the cover panel behind the door handle by prying out the cover with a panel tool.
  • Open the cover near the top of the grab handle to reveal a phillips head bolt.
  • Open the cover at the bottom of the grab handle to reveal a phillips head bolt.
  • Remove the three phillips head bolts using a screwdriver.
  • Remove the door panel by grabbing the bottom of the panel and pull back with your fingers.
  • Lift the door panel up and off the window ledge.
  • Disconnect the door latch and locking wire by removing the connector from the hold, swivel the ball up and out of the mechanism. Depress and remove the connections for the window switch and courtesy light.
  • If any of the retaining clips for the door panel stayed in the door, now is the time to remove them using a panel removal tool and insert them back into the door panel.
Step 7

Removal and replacement of the 6.5 inch rear door speaker:
  • Disconnect the factory speaker wire from the top of the speaker by depressing the tab.
  • Using a 10mm socket, remove the three screws that secure the factory speaker.
  • Place the Focal speaker into the opening, making sure to line up all four holes to the factory mounting location.
  • Secure the speaker to the door using the factory screws.
  • Connect the door speaker harness into the speaker housing.
Repeat the process for the other rear door speaker.

Step 8

Replace the rear door panel:
  • Connect the window switch panel, courtesy light, door lock wire and door handle wire.
  • Hang the door on the window ledge and push down into place.
  • Once the door panel is lines up, push in to secure the retaining clips.
  • Secure the three phillips head screws: Located behind the door handle, at the top on the grab handle and at the bottom of the grab handle.
  • Replace the cover plate behind the door handle.
Step 9

Remove the rear hatch cover:
  • Remove the pull handle trim piece by prying out with a panel removal tool or small screwdriver.
  • Remove the pull strap using a 10mm socket to remove the bolt.
  • Remove the hatch light assemblies by prying out on one side.
  • Pry in the slot on the drivers side of each light to release the spring tab.
  • Depress the tab to release the wiring harness.
  • Repeat for both lights
  • Remove the hatch cover by releasing the retaining clips around the edge by pulling with your fingers.
  • Lift the cover up and off the window ledge.
  • If any of the retaining clips for the door panel stayed in the door, now is the time to remove them using a panel removal tool and insert them back into the door panel.
Step 10

Remove the factory hatch 6.5 inch speaker:
  • Depress the tab and remove the factory wiring connector.
  • Using a phillips head screw driver or 10mm socket, remove the three bolts that secure the factory 6.5 inch speaker to the door panel.
Step 11

Installing your new Focal 6.5 inch rear door speakers:
  • Disconnect the factory speaker wire from the top of the speaker by depressing the tab.
  • Using a 10mm socket, remove the three screws that secure the factory speaker.
  • Place the Focal speaker into the opening, making sure to line up all four holes to the factory mounting location.
  • Secure the speaker to the door using the factory screws.
  • Connect the door speaker harness into the speaker housing.
Repeat the process for the other hatch speaker.

Step 12

Replace the rear hatch cover:
  • Hang the hatch cover over the window ledge.
  • Line up the retaining tabs and push into place. Push around the edge and in the middle of the panel.
  • Install the pull handle by securing the 10mm bolt.
  • Replace the pull handle cover piece
  • Connect the courtesy lights harnesses and insert them back into the hatch.
Step 13

Test your new Focal speakers!

Pro Tip: These are new speakers and they operate the best following a break in. Go easy on them and break them in easy.

Congratulations on installing your new Focal 8 Speaker Plug & Play Bundle!

Back to blog